How To Repair Bulging Plaster Walls

Download Article

Download Article

If your home or business was built before the 1950s or synthetic using traditional methods, there'south a good chance it has plaster walls. With fourth dimension, the paint or meridian coat of plaster can commencement to come loose. Fortunately, in that location are some relatively simple means you can repair your plaster walls if you discover peeling or other wear and tear. Nosotros've put together this handy Q and A commodity to help you lot and your plaster walls out!

1. one

   Perchance the plaster wasn't fully dry before it was painted. If your walls are newly plastered and painted, the paint tin can start to flake off if in that location is still wet in the plaster underneath. Plaster must be fully dry before you paint it.^[ane]

   • It usually takes at to the lowest degree a few days for plaster to dry out completely, but it's recommended to wait at least i week to paint newly plastered walls.
   • Fully dry plaster is a light creamy pink color.

2. 2

   Layers of paint can start peeling off old plaster because of the buildup. It's mutual for people to just slap on new coats of paint to freshen upwards plaster walls over the years. However, when then many layers of paint are applied to sometime plaster, the walls oftentimes commencement to peel.^[2]

   • If information technology seems like the paint is peeling because there are also many old coats, sand or scrape off the old paint and repaint the plaster.
   • Paint tin can as well flake off if the plaster wasn't primed before the glaze of paint was applied.

   Advertisement

3. 3

   Excessive moisture can cause the summit layer of plaster to peel up. There are typically iii coats of plaster applied to any plastered wall: the scratch coat, the intermediate coat, and the top coat or hard coat. The top glaze is the thinnest layer and therefore can pop up from the substrate layers if it gets damp ofttimes.^[iii]

   • This is most common on outside walls, bathroom walls, and kitchen walls, but it can happen anywhere.
   • Changes in temperature from twenty-four hours to night and due to air-conditioning can also make plaster walls moist.

Ad

1. one

   Brainstorm by scraping abroad all the peeling paint. Scrape off all the loose paint flakes with the border of a putty pocketknife. Move the putty knife back and forth across the whole area, changing management occasionally, to get rid of all the peeling paint.^[4]

   • This also lets you see the plaster below the paint and make certain it is nonetheless solid and not flaking off the substrate layers. As long as the height glaze of the plaster isn't loose, yous can proceed with paint prep.

2. 2

   Polish the edges of the remaining paint with sandpaper. Put a piece of fine-dust sandpaper, such as 1500-grit or 2000-dust sandpaper, on a small sanding block. Rub it back and forth over the edges of the intact paint around the peeled area to blend them in.^[v]

   • Note that if there is whatever plaster damage below the paint, you lot must repair information technology first before yous continue to repaint the surface area. You can practice this by patching it with joint chemical compound or patching plaster.

3. 3

   Prime the damaged area. Use a paint brush to brush one coat of plaster primer onto the peeled area. Let the primer dry for at least i 60 minutes before yous move on to painting it.^[6]

   • If you repaired whatever damaged plaster, make sure to wait at least 3 days and preferably 1 week for information technology to dry before priming and painting it.

Advertisement

1. i

   Drill pilot holes into the plaster on both sides of the crevice. Utilise a 3/16-inch (4.76 mm) masonry fleck to drill a pigsty well-nigh 2 in (v.1 cm) from the crack on 1 side. Do the aforementioned on the contrary side, so the holes are about 4 in (x cm) apart. Make a series of holes about three in (vii.6 cm) autonomously from each other forth each side of the crack.^[9]

   • The masonry bit won't become through the wooden lath beneath the plaster, so only back the drill out every bit shortly as you lot feel it hit wood.

2. two

   Inject plaster repair agglutinative into the holes. Vacuum the plaster crumbs out of all the holes first. Then, squeeze plaster repair adhesive into each hole using a caulking gun.^[x]

   • Notation that this is intended to help the plaster re-adhere to the board below and forestall farther separation of the plaster when in that location is a really deep cleft. If the scissure is just in the top layer of plaster, you tin can patch it with articulation compound or repair plaster.

3. 3

   Screw the plaster into the board below and let the glue dry. Identify a two in (v.1 cm) plastic washer over a v/eight-inch (15.87 mm) drywall screw for each hole yous drilled. Drive the screws through each of the holes, all the style into the wooden board beneath. Wait ane-2 days, then remove the screws and washers.^[eleven]

   • Wipe off any backlog adhesive that oozes out of the holes with a moisture sponge.
   • You should see the crack shrink as the screws pull the separating plaster back together.
   • If there is nonetheless a small crevice subsequently you remove the screws, fill it in with articulation compound or repair plaster and prime and paint over it.

Advertisement

Inquire a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertisement

Cheers for submitting a tip for review!

Well-nigh This Article

Thanks to all authors for creating a page that has been read 21,536 times.

Did this article assist you?

Source: https://www.wikihow.com/Repair-Peeling-Plaster-Walls

Share this post